Only water distiller on the market with faucets
that are ALL STAINLESS STEEL. Other distillers use plastic housings,
with rubber gaskets and plastic nuts in the inside of the tank to hold
it on. Ours does not !
Larger Drain than most other water distillers.
Although some distillers claim they have such and such size valve, most
taper down into a 3/8" tube restricting flow. Our distiller is a
FULL 1/2" drain tube, allowing easier draining.
These are the devices that detect the water level
in the boiling chamber and holding tank. Detection is done via conductance,
eliminating ALL mechanical switches, moving parts, and seals other water
distillers use for detecting water level. This eliminates many of
the failure parts in most other water distillers, and eliminates PLASTIC
float sitting in your water.
This is the heart of all auto fill American Water
Distillers. This circuit eliminates the necessity of manual sterilization.
Our water distillers sterilize themselves on a regular basis, eliminated
the need to manually sterilize the unit, and also sterilizing it more often,
keeping your distiller germ free!
Stainless Steel coil, with Volatile Escape Vent,
and electronic circuit board. Also, our fan is protected with a shroud,
eliminating the possibility of the coil hitting the fan blade during shipping.
Water Distiller Solenoid Valve, stainless steel
construction. Also notice on the right, that is where the water line
is connected to an outline water source. The connector is made out
of stainless steel, not plastic. Our water distillers are the only
ones were aware of constructed with such high quality material.
This is the 'Whistle'. It whistles when your hot
water boiling chamber has reached the proper temp, letting you know it's
ready for you to make hot tea or coca with boiling hot distilled water.
(9HC model only)
Double distillation showing distilled water going
into 2nd tank for distillation. Only consumer water distiller with
this feature. Usually reserved for scientific labs. (9HC model only)
Only Water Distiller on the market with a Stainless
Steel Heating Element! Other distiller elements are similiar to what
is used in an oven, and crack/break easy during cleaning.
And of course, in the rare instance something breaks,
we have parts, IN STOCK! No Down time! (exceptions apply call for details)
Dimensions: 18" High
18" Long 12" Deep
Weight: 48 Lbs model
9C (51 Lbs 9HC Water Distiller)
Electrical: 120V 1200
Watt (Other voltages available)
Coconut Charcoal Carbon
pre Filter good for 1,500 Gallons
Purity: 0 PPM on TDS
> 99.9 Percent Purity. (9C Model)
Purity: 0 PPM on TDS
> 99.99999 (9HC Model)
Super Large Carbon Filter removes VOC's prior to distillation.
Eliminating possibility of collected contaminants being released from filter
directly into distilled water. Last 1 1/2 years if you make 3 gallons
Volatile chemicals that boil at a temperature lower
than water (chlorine is a good example), unless removed prior to distillation,
either go back into the distilled water or, more commonly, be
vaporized into the air of your home. Breathing them is as
bad as drinking them. The best policy is to filter the water through carbon
before distilling it. Our water distiller removes them PRIOR to distillation!
No dangerous VOC's will be released into your house to breath!
Made out of 304 Stainless Steel. No Plastic faucet,
no plastic fittings, no plastic float parts, no plastic lid knobs !
GAC system also reduces hard water deposits, meaning
Auto Sterilization, keeps water distiller germ free.
V shaped boiling chamber.
NO PLASTIC or rubber gaskets that touch the water
in the boiling chamber.
No floats or mechanical devices to get knocked around
or out of alignment during shipment.
1 Piece unit, no assembly or wiring necessary. Much
easier and quicker to hook up compared to other water distillers.
Most other water distillers require the top to be hooked up to the bottom,
and screws/nuts/rubber washers must be held tightened up from the INSIDE
of the holding tank of the water distiller, which is not easy. And wiring
harnesses must be attached. Our drain valves are already installed
on the water distiller. All the customer has to do with our water
distillers is screw the faucet on the front by hand, no tools needed, and
attach an incoming water line to the distiller. No other automatic
water distiller is this easy to hook up.
Hot/Cold model double distills water. If
you think water that is distilled once is pure, it's much more pure if
it's double distilled!
Water distiller has a completely removable boiling
chamber lid, which provides the easiest access in the industry to the stainless
steel boiling chamber itself.
All American Water Distiller functions are controlled
by modern solid-state circuitry. All American Water Distiller units
have no mechanical floats, float seals or microswitches to leak, fail,
leach, or require replacement. And the plug-in connectors make servicing
the water distiller a breeze!.
you appreciate our
marketing method, that cuts out the middle man, and saves you $$$$$
Instead of distributors and dealers taking a cut, we put the savings in
your pocket! Giving you a far superior water distiller, at a lower
NSF® certified pump $89
Auto Drains also available